AMCOM AM153040WM-FM-R: Specifications & Applications

The AMCOM AM153040WM-FM-R is a two-stage GaAs HiFET pHEMT MMIC power amplifier designed for RF applications covering 1.4GHz to 3.4GHz. It provides 18dB typical small-signal gain, 37dBm typical output power at the 1dB compression point (P1dB), and 38dBm typical saturated output power under specified test conditions.

The FM version features a ceramic MMIC mounted on a gold-plated copper flange, providing a mechanical interface for heat-sink installation. It is suitable for selected wireless communication, RF transmission and microwave system applications.

1. AM153040WM-FM-R Specifications

Test conditions: VDD = +12V, VGS approximately -0.90V, IDQ = 1300mA and ambient temperature = 25°C. The gate voltage may vary between production lots and should be adjusted to obtain the specified quiescent drain current.

Frequency note: The 1.4–3.4GHz range represents application coverage. The manufacturer's published minimum performance specifications are provided over 1.8–3.0GHz. Verify the RF performance curves at the intended operating frequency before finalizing a design.

2. RF Performance: Gain and Output Power

The AM153040WM-FM-R combines broadband gain with relatively high output power for its frequency range.

• 18dB typical gain: Provides RF amplification across the specified application band.

• 37dBm typical P1dB: Equivalent to approximately 5W of RF output power at the 1dB compression point.

• 38dBm typical Psat: Equivalent to approximately 6.3W at saturation.

• 43dBm typical IP3: A key parameter for evaluating intermodulation performance.

These are typical specifications under the manufacturer's stated test conditions, not guaranteed values at every frequency. For modulated signals, engineers should also evaluate output back-off, linearity, spectral requirements and thermal performance.

3. FM Package and Thermal Management

The AM153040WM-FM-R is the AM153040WM-BM-R MMIC mounted on a gold-plated copper flange carrier. The flange includes mounting holes for attachment to a suitable metal heat sink.

Because the amplifier draws approximately 1.3A of quiescent drain current at a nominal 12V supply, thermal design is an important part of system integration.

• Provide a suitable metal heat sink and low-resistance thermal interface.

• Follow the manufacturer's package drawing and mounting recommendations.

• Use appropriate RF grounding and supply decoupling.

• Monitor device temperature during initial power-up and high-power operation.

The datasheet specifies a typical thermal resistance of 5°C/W. Actual junction temperature depends on dissipated power, mounting conditions and heat-sink performance.

4. Bias Requirements and Pin Configuration

The AM153040WM-FM-R uses separate drain and gate connections for its two amplifier stages.

Critical bias warning: Establish the required negative gate biases at VGS1 and VGS2 before applying the drain supply voltages. Follow the official test circuit and bias-sequencing instructions.

The manufacturer's recommended quiescent drain currents are approximately 300mA for the first stage and 1000mA for the second stage. Adjust gate bias according to the datasheet rather than assuming that -0.90V is an exact setting for every device.

5. AM153040WM-FM-R Applications

• PCS base stations: RF amplification in compatible transmit signal chains.

• GPS-related equipment: Selected RF transmission and subsystem applications where the frequency and power requirements are appropriate.

• MMDS equipment: Microwave distribution systems operating within the amplifier's application range.

• WLAN repeaters: RF amplification in compatible repeater designs.

• RF test equipment: Microwave signal generation, evaluation and test applications requiring broadband amplification.

Final suitability depends on the operating frequency, required linear output power, RF drive level, bias conditions and heat-sink design.

6. AM153040WM-FM-R vs BM-R vs EM-R

AMCOM offers the AM153040WM family in different package configurations.

These package variants belong to the same amplifier family but should not automatically be treated as mechanically interchangeable. Verify the package drawing, lead configuration, mounting dimensions and thermal requirements before selecting a substitute.

7. Official Datasheet

Refer to the manufacturer documentation for complete electrical characteristics, performance curves, absolute maximum ratings, pin assignments and test circuits.

Download AM153040WM-BM/EM/FM-R Datasheet – Rev. 1, June 2019 (PDF)

For surface-mount implementation, consult the manufacturer's application note AN700. The datasheet specifies additional derating and thermal requirements for PCB-only mounting.

8. AMCOM AM153040WM-FM-R Price, Availability & RFQ

Looking for AMCOM AM153040WM-FM-R for a new RF design, replacement project or production order?

DataStorageIC can assist with sourcing inquiries and quotation requests for AMCOM RF power amplifiers.

To request a quotation, please provide:

• Part number: AM153040WM-FM-R

• Required quantity

• Target price, if available

• Required delivery date

• Destination country or region

• Required documentation or packaging requirements

Availability, price and lead time are subject to confirmation.

Request pricing and availability: Visit DataStorageIC and submit your requirements through the website inquiry form.

Related AMCOM Resources

• AMCOM In-Stock Products – Browse listed AMCOM models and submit sourcing inquiries.

• AMCOM GaN MMIC Power Amplifier Selection Guide – Explore a different RF amplifier technology and compare power amplifier selection criteria.

• DataStorageIC RF & Microwave Components – Submit RF component and BOM sourcing requests.